Configuring Multiarea OSPFv3 6.2.3.7

RA>ena
RA#conf t
RA#conf terminal
Enter configuration commands, one per line.  End with CNTL/Z.
RA(config)#hostname deviwi
deviwi(config)#ipv6 unicast-routing
deviwi(config)#ipv6 roter ospf 1
                      ^
% Invalid input detected at '^' marker.
   
deviwi(config)#ipv6 router ospf 1
%OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id,please configure manually
deviwi(config-rtr)#router-id 1.1.1.1
deviwi(config-rtr)#ex
deviwi(config)#int gig
deviwi(config)#int gigabitEthernet 0/0
deviwi(config-if)#ipv6 ospf 1 area 1
deviwi(config-if)#ex
deviwi(config)#int gigabitEthernet 0/1
deviwi(config-if)#ipv6 ospf 1 area 1
deviwi(config-if)#ex
deviwi(config)#int serial 0/0/0
deviwi(config-if)#ipv6 ospf 1 area 0
00:06:18: %OSPFv3-5-ADJCHG: Process 1, Nbr 11.11.11.11 on GigabitEthernet0/0 from LOADING to FULL, Loading Done

deviwi(config-if)#ex
deviwi(config)#
00:06:38: %OSPFv3-5-ADJCHG: Process 1, Nbr 12.12.12.12 on GigabitEthernet0/1 from LOADING to FULL, Loading Done


RB>ena
RB>enable

RB#conf t
RB#conf terminal
Enter configuration commands, one per line.  End with CNTL/Z.
RB(config)#hostname deviwiy
deviwiy(config)#ipv6 unicast-routing
deviwiy(config)#ipv6 router ospf 1
%OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id,please configure manually
deviwiy(config-rtr)#router-id 2.2.2.2
deviwiy(config-rtr)#ex
deviwiy(config)#int gi
deviwiy(config)#int gigabitEthernet 0/0
deviwiy(config-if)#ipv6 ospf 1 area 0
deviwiy(config-if)#ex
deviwiy(config)#int serial 0/0/0
deviwiy(config-if)#ipv6 ospf 1 area 0
deviwiy(config-if)#e
00:09:18: %OSPFv3-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0/0 from LOADING to FULL, Loading Done

% Ambiguous command: "e"
deviwiy(config-if)#ex
deviwiy(config)#int serial 0
00:09:38: %OSPFv3-5-ADJCHG: Process 1, Nbr 21.21.21.21 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
/0/1
deviwiy(config-if)#int serial 0/0/1
deviwiy(config-if)#ipv6 ospf 1 area 0
deviwiy(config-if)#ex
deviwiy(config)#


inhos

RC>ena
RC#conf t
RC#conf terminal
Enter configuration commands, one per line.  End with CNTL/Z.
RC(config)#hostname deviwiyen
deviwiyen(config)#ipv6 unicast-routing
deviwiyen(config)#ipv6 router ospf 1
%OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id,please configure manually
deviwiyen(config-rtr)#router-id 3.3.3.3
deviwiyen(config-rtr)#ex
deviwiyen(config)#int gi
deviwiyen(config)#int gigabitEthernet 0/0
deviwiyen(config-if)#ipv6 ospf 1 area 2
deviwiyen(config-if)#ex
deviwiyen(config)#int gigabitEthernet 0/1
deviwiyen(config-if)#ipv6 ospf 1 area 2
deviwiyen(config-if)#ex
deviwiyen(config)#int serial 0/0/1
deviwiyen(config-if)#
00:13:13: %OSPFv3-5-ADJCHG: Process 1, Nbr 31.31.31.31 on GigabitEthernet0/0 from LOADING to FULL, Loading Done

deviwiyen(config-if)#ipv6 ospf 1 area 0
deviwiyen(config-if)#
00:13:30: %OSPFv3-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Serial0/0/1 from LOADING to FULL, Loading Done

deviwiyen(config-if)#
00:13:32: %OSPFv3-5-ADJCHG: Process 1, Nbr 32.32.32.32 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
ex
deviwiyen(config)#